Toymaker Television

Daily content for the geek and DIYer



Posts tagged microphone preamp

2 notes &

Cascade Microphone Preamp v0.02

So we’ve had a few questions from tumblr readers about the cascade preamp that Whisker made so to help anyone else who might be looking for an updated schematic:

These are only good with low-impedance microphones such as our Cascade Ribbon Mic or Shure 55SH.  And here’s the previous article that we had a few comments on:

http://tymkrs.tumblr.com/post/9168179996/diy-microphone-preamp

Hope this helps and let us know if there are any questions!

@atdiy/@tymkrs 

Filed under cascade preamp schematic tymkrs low impedance microphone diy microphone preamp diy microphone preamp

27 notes &

DIY Microphone Preamp

So @makerdino and @brainwagon as well as @whixr have been working on creating, analyzing, and optimizing a simple common-emitter preamp circuit that Dino made for his Hackaweek project. 

The above schematic is quite similar to the one that Dino used and was partially analyzed in my electret preamplifier circuit post.  Whisker took the circuit and added a few bits. 

If we look at this generally, there is a capacitor from the microphone to the circuit, and a capacitor from the circuit to the output.  These serve to filter out any dc current and only allow ac current, or the audio signal, through.  These are known as coupling capacitors as highlighted below:

Since starting the writing of this, @brainwagon has discovered that because the microphones we use are not specifically electret microphones, the first resistor (R1 next to C1) is unnecessary as that resistor was helping meter power to specifically electret microphones.  Highlighted below!

Adjusting that resistor’s value does nothing for gain or function.  So we will in the future, take that resistor out, and even C1, so that the audio input goes through C2 to the amplifying transistor. **EDIT** It worked! The removal of R1 and C1 shown above led to no discernible difference in function or gain!

Now, the middle R1 serves to provide the power to the transistor that will be considered the amplified current.  R2 contributes to how the audio signal will affect the base of the transistor. 

  • In the electret preamplifier circuit, I thought this particular resistor (R2) prevented the power from influencing the audio signal and vice versa, but I believe that somehow the power is added onto the signal to help it affect the base of the transistor.  I don’t know the exact mechanics, but if its role were only to prevent the power rail from affecting the audio signal, then there wouldn’t be an electric connection at all.  Right?

Anyway so Whisker originally used a wire instead of R3, but that resulted in an ear-splitting squeal, so using the below tip, he found that a resistor worked nicely to bring the voltage down (to an appropriate but not severely diminished level) before the second amplification stage.

  • Tip: Using a potentiometer (or variable resistor), you can tune to see which specific resistance value works best for the circuit.  Then you can take out the potentiometer and put the “hardcoded” resistor in.

So now - the audio signal that has been slightly attenuated, again gets dc current filtered out.  And then encounters the same R1-R2-3N3904 amplification portion. 

Then finally, it encounters the last coupling capacitor for a last minute filter of any dc badness.  Then onward and forward to the output!  We put the output of the preamp into our mixer which fed the computer.

We will have a demonstration of this on youtube but what I can tell you is that we were able to amplify a Cascade long ribbon mic, Nady-rsm4 ribbon mic, Shure 55SH, and PG48 mic with such clean results that it pretty much sounds like our professional preamp that cost 500 bucks. 

Try it for yourself, let us know how it worked for you?

Whee!

(PS We called it a cascade preamp because of the two stages of amplification in series, but also because it works for our cascade microphone - punpunpun!)

@atdiy/@tymkrs

Filed under common emitter preamplifier circuit coupling capacitors preamplifier circuit diy electronics microphone preamp how do preamplifiers work how do preamps work tymkrs